2005-04-29 -+- Khayan -+- khayansa@gmail.com -+- Hello,I like your web page.I am  a beginner of AVR.Can you introduce me how i start. -+- 203.185.130.17 = Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1)
2005-05-06 -+- marc geonet -+- pin88303@scarlet.be -+- hi <br> <br>ireally got interest with this artikel <br>this is my first try to program microcontroller <br>ok <br>i got a problem: i got all the stuffs at the shop, now i try the thermometer. <br>I passed the tests with success, i loaded the atmel with success, but when i run the i2ctemp_linux program, it answers me "ERROR: address_slave for write failed" <br> <br>what should i do, did i do a mistake somewhere <br>couls you help me <br> <br>thanks <br> <br>marc <br> -+- 213.49.91.211 = Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.7.6) Gecko/20050223 Firefox/1.0.1
2005-05-07 -+- Guido Socher -+-   -+- Hello Marc, <br>Do you have a LCD display? <br>If not then make sure that you use the software for <br>part I of the article series. Part II (linuxI2Ctemp_lcd-0.5) will not <br>work because there is no response from the LCD display. The microcontroller <br>will then hang and wait for the display to answer, which will never happen. <br> <br> -+- 195.71.95.98 = Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.7.7) Gecko/20050414 Firefox/1.0.3
#2005-05-20 -+- alireza -+- ali77_ir -+- in the name of god <br>hello <br>very good <br>map application  <br>I have problem noise if you can help my  <br> I can not read english well -+- 217.218.221.21 = Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; .NET CLR 1.1.4322)
2005-07-16 -+- Roberto -+- roberto.polsinelli@aliceposta.it -+- Hi Guido, <br>I made all the connections and I read the temp from the RS232 port but I do not see anything in the display...I tried with 2 different display but no line comes out. Do I have to remove the resistor for the contrast? <br>Thank you in advance <br>Roberto -+- 82.53.148.42 = Mozilla/5.0 (X11; U; Linux i686; it-IT; rv:1.7.8) Gecko/20050511 Firefox/1.0.4
2005-07-17 -+- Guido Socher -+-   -+- Hello Roberto, <br>max contrast is when you connect the contrast pin to GND. <br> <br>However check also each and every pin against the datasheet. <br>Especially make sure that you do not mix up +5V and GND at the <br>display.  -+- 195.71.95.98 = Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.7.9) Gecko/20050711 Firefox/1.0.5
#2006-05-11 -+- Bukhari Adam -+- bukhariadam@hotmail.com -+- Hello  <br> <br>Could you please help me, I have a CaseStudy for Digital Thermometer with Analogue Display, <br>by using a temperature sensor such as LM35.Convert the analoue output of the sensor in to digitl using the ADC card in the PC. Design appropriate conditioning circuit to match the sensor output to ADC input. Use the PC monitor as the main display. Design a circular dial display or bar graph display to show the actual temperature <br>the display range should be 0 to 100 degrees centigrade <br> <br>please try to help me by C++ Programming Commands <br> <br>Thank you <br> <br>B. Adam -+- 163.167.210.100 = Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1; .NET CLR 1.1.4322; .NET CLR 2.0.50727)